P2195 Code — O2 Sensor Signal Stuck Lean Bank 1 Sensor 1

P2195: O2 Sensor Signal Stuck Lean Bank 1 Sensor 1. This is a Powertrain trouble code — a manufacturer-specific code whose exact meaning can vary by carmaker. Severity is generally Medium.

Medium priority

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

What the P2195 code means

CodeP2195
DefinitionO2 Sensor Signal Stuck Lean Bank 1 Sensor 1
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeManufacturer-specific
SubsystemFuel and air metering
Fault referenceFault #95 within the Powertrain group
Typical severityMedium

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a manufacturer-defined code, so confirm the exact meaning against your carmaker's service information. Within powertrain codes, it points to the fuel and air metering area.

Common causes of P2195

P2195 sits in the SAE range covering oxygen (O2) sensor circuit. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • An aged sensor with slow voltage response.
  • A failed heater element or its fuse/relay circuit.
  • Contamination from coolant, oil or fuel additives.
  • An exhaust leak upstream of the sensor skewing the reading.
  • Wiring or connector faults (chafing near the exhaust is common).

Symptoms you may notice with P2195

Codes in the oxygen (O2) sensor circuit range typically show up like this:

  • Poor fuel economy.
  • Rough idle or hesitation.
  • A failed emissions test.
  • Often no drivability change (heater faults).

How to fix a P2195 code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: watch the sensor switching frequency live at 2,000 rpm, confirm heater resistance against spec, and check for exhaust leaks before condemning the sensor.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

Related OBD-II codes

Frequently Asked Questions

What does P2195 mean?

P2195 is a Powertrain diagnostic trouble code that means: O2 Sensor Signal Stuck Lean Bank 1 Sensor 1. It is Manufacturer-specific — the exact meaning can vary by carmaker.

Is it safe to drive with a P2195 code?

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

How do I fix a P2195 code?

Confirm P2195 with an OBD-II scanner, then work the ranked fixes below: start with inspect for exhaust leaks near the o2 sensor (most probable, Easy DIY), verify with a re-scan after each repair. Estimated repair cost ranges from $5 to $106 including labor (editorial estimate, US aftermarket).

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap">

Most likely fixes for P2195, ranked

Ranked by how often the fix resolves the code, based on VinSpecs editorial analysis of US aftermarket repair patterns. Costs are editorial estimates for US aftermarket parts and shop labor (about $110/hour); actual quotes vary by vehicle, region and shop — get a real quote before authorizing work.

1. Inspect for exhaust leaks near the O2 sensor

Probability rank #1 · Difficulty: Easy DIY · Estimated total: $5–$106 (parts $5–$40 + labor 0.6 h)

  1. 1. Inspect the exhaust manifold and pipe joints near the sensor bung for leaks
  2. 2. Listen and smoke-test for exhaust leaks upstream of the sensor
  3. 3. Replace gaskets or tighten fasteners as needed
  4. 4. Clear codes and monitor sensor voltage trace

Parts/tools involved: Exhaust manifold/pipe gasket.

2. Replace oxygen sensor

Probability rank #2 · Difficulty: Moderate DIY · Estimated total: $50–$246 (parts $50–$180 + labor 0.6 h)

  1. 1. Identify the affected bank/sensor position
  2. 2. Remove the sensor with an O2 sensor socket
  3. 3. Apply anti-seize to threads (avoid the tip) and install the new sensor
  4. 4. Clear codes and confirm a normal switching voltage trace

Parts/tools involved: Oxygen sensor (bank/position-specific), Anti-seize compound.

3. Repair O2 sensor signal circuit wiring

Probability rank #3 · Difficulty: Professional Required · Estimated total: $10–$192 (parts $10–$60 + labor 1.2 h)

  1. 1. Back-probe the signal and ground at the connector with the engine running
  2. 2. Voltage-drop test the circuit back to the ECM
  3. 3. Repair chafed or corroded wiring near the exhaust with high-temp splices
  4. 4. Confirm proper switching activity

Parts/tools involved: High-temperature wiring repair kit.

Cost basis: VinSpecs editorial dataset obd-editorial-us-aftermarket-v1 (US aftermarket, generated 2026-11-14). Verify the diagnosis on your specific vehicle before replacing parts. Report a data error.

← All OBD-II codes Decode your VIN →