P2135 Code — Throttle/Pedal Pos Sensor/Switch A / B Voltage Correlation

P2135: Throttle/Pedal Pos Sensor/Switch A / B Voltage Correlation. This is a Powertrain trouble code — a manufacturer-specific code whose exact meaning can vary by carmaker. Severity is generally Medium.

Medium priority

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

What the P2135 code means

CodeP2135
DefinitionThrottle/Pedal Pos Sensor/Switch A / B Voltage Correlation
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeManufacturer-specific
SubsystemFuel and air metering
Fault referenceFault #35 within the Powertrain group
Typical severityMedium

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a manufacturer-defined code, so confirm the exact meaning against your carmaker's service information. Within powertrain codes, it points to the fuel and air metering area.

Common causes of P2135

P2135 sits in the SAE range covering throttle body and pedal position. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • Carbon buildup around the throttle plate (the most common cause).
  • A failing throttle position (TPS) or accelerator pedal position (APP) sensor.
  • A worn throttle motor or gear (electronic throttle).
  • A lost calibration after a battery disconnection.

Symptoms you may notice with P2135

Codes in the throttle body and pedal position range typically show up like this:

  • High or hanging idle.
  • Hesitation or a dead pedal feel.
  • Limp mode with reduced power.
  • Stalls at stops.

How to fix a P2135 code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: clean the throttle plate bore first, then check TPS/APP voltage sweep across the pedal travel and re-learn the idle after cleaning.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

Related OBD-II codes

Frequently Asked Questions

What does P2135 mean?

P2135 is a Powertrain diagnostic trouble code that means: Throttle/Pedal Pos Sensor/Switch A / B Voltage Correlation. It is Manufacturer-specific — the exact meaning can vary by carmaker.

Is it safe to drive with a P2135 code?

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

How do I fix a P2135 code?

Confirm P2135 with an OBD-II scanner, then work the ranked fixes below: start with inspect and clean throttle/pedal position sensor connector (most probable, Easy DIY), verify with a re-scan after each repair. Estimated repair cost ranges from $5 to $64 including labor (editorial estimate, US aftermarket).

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap">

Most likely fixes for P2135, ranked

Ranked by how often the fix resolves the code, based on VinSpecs editorial analysis of US aftermarket repair patterns. Costs are editorial estimates for US aftermarket parts and shop labor (about $110/hour); actual quotes vary by vehicle, region and shop — get a real quote before authorizing work.

1. Inspect and clean throttle/pedal position sensor connector

Probability rank #1 · Difficulty: Easy DIY · Estimated total: $5–$64 (parts $5–$20 + labor 0.4 h)

  1. 1. Locate the throttle body or accelerator pedal assembly connector
  2. 2. Unplug and inspect for corrosion or bent pins
  3. 3. Clean contacts and reseat firmly
  4. 4. Clear codes and verify smooth voltage sweep

Parts/tools involved: Electrical contact cleaner.

2. Replace throttle body or pedal position sensor assembly

Probability rank #2 · Difficulty: Moderate DIY · Estimated total: $60–$368 (parts $60–$280 + labor 0.8 h)

  1. 1. Unplug the connector and remove the mounting fasteners
  2. 2. Install the replacement throttle body or pedal assembly
  3. 3. Reconnect and perform a throttle relearn if required
  4. 4. Clear codes and verify all channels track together

Parts/tools involved: Electronic throttle body assembly, Accelerator pedal position sensor assembly.

3. Repair throttle/pedal position sensor wiring

Probability rank #3 · Difficulty: Professional Required · Estimated total: $10–$203 (parts $10–$60 + labor 1.3 h)

  1. 1. Back-probe the reference, signal, and ground circuits at the connector
  2. 2. Voltage-drop test each leg back to the ECM
  3. 3. Repair chafed conductors with heat-shrink splices
  4. 4. Confirm all sensor channels agree throughout the pedal/throttle sweep

Parts/tools involved: Automotive wiring repair kit (solder + heat-shrink).

Cost basis: VinSpecs editorial dataset obd-editorial-us-aftermarket-v1 (US aftermarket, generated 2026-11-14). Verify the diagnosis on your specific vehicle before replacing parts. Report a data error.

← All OBD-II codes Decode your VIN →