P0720 Code — Output Speed Sensor Circuit Malfunction

P0720: Output Speed Sensor Circuit Malfunction. This is a Powertrain trouble code — a generic OBD-II code that means the same thing on every make and model. Severity is generally Medium.

Medium priority

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

What the P0720 code means

CodeP0720
DefinitionOutput Speed Sensor Circuit Malfunction
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeGeneric (SAE J2012 standard)
SubsystemTransmission
Fault referenceFault #20 within the Powertrain group
Typical severityMedium

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a standardized SAE code, so the definition above applies to any OBD-II compliant vehicle from 1996 onward. Within powertrain codes, it points to the transmission area.

Common causes of P0720

P0720 sits in the SAE range covering vehicle speed sensor circuit. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • A failing VSS (magnetic or Hall-effect).
  • A damaged tone ring the sensor reads.
  • Wiring between the sensor, the cluster and the modules.
  • ABS-module path faults where the speed signal routes through it.

Symptoms you may notice with P0720

Codes in the vehicle speed sensor circuit range typically show up like this:

  • Speedometer dead or erratic.
  • Cruise control dropping out.
  • Erratic or harsh shifting (the TCM uses the signal).
  • ABS or traction lights.

How to fix a P0720 code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: watch the speed signal live while rolling and compare it against ABS wheel-speed data to see exactly where the signal is lost.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

Related OBD-II codes

Frequently Asked Questions

What does P0720 mean?

P0720 is a Powertrain diagnostic trouble code that means: Output Speed Sensor Circuit Malfunction. It is Generic (SAE standard) — the same meaning on every OBD-II vehicle.

Is it safe to drive with a P0720 code?

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

How do I fix a P0720 code?

Confirm P0720 with an OBD-II scanner, then work the ranked fixes below: start with inspect output shaft speed sensor connector (most probable, Easy DIY), verify with a re-scan after each repair. Estimated repair cost ranges from $5 to $75 including labor (editorial estimate, US aftermarket).

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap">

Most likely fixes for P0720, ranked

Ranked by how often the fix resolves the code, based on VinSpecs editorial analysis of US aftermarket repair patterns. Costs are editorial estimates for US aftermarket parts and shop labor (about $110/hour); actual quotes vary by vehicle, region and shop — get a real quote before authorizing work.

1. Inspect output shaft speed sensor connector

Probability rank #1 · Difficulty: Easy DIY · Estimated total: $5–$75 (parts $5–$20 + labor 0.5 h)

  1. 1. Locate the sensor connector at the transmission tail housing/case
  2. 2. Disconnect and inspect for fluid intrusion/corrosion
  3. 3. Clean and reseat with a fresh seal
  4. 4. Clear the code and road test

Parts/tools involved: Dielectric grease.

2. Replace output shaft speed sensor

Probability rank #2 · Difficulty: Moderate DIY · Estimated total: $25–$178 (parts $25–$90 + labor 0.8 h)

  1. 1. Raise the vehicle and locate the sensor at the transmission tail housing
  2. 2. Remove its retaining bolt and withdraw the sensor, catching any fluid drip
  3. 3. Install the replacement sensor with a new O-ring, seated fully
  4. 4. Clear the code and confirm output speed tracks vehicle speed

Parts/tools involved: Output shaft speed sensor, Sensor O-ring.

3. Repair output shaft sensor wiring

Probability rank #3 · Difficulty: Professional Required · Estimated total: $30–$348 (parts $30–$150 + labor 1.8 h)

  1. 1. Back-probe the sensor circuit at the TCM connector
  2. 2. Trace the internal/external harness for chafing
  3. 3. Repair or replace the affected harness section
  4. 4. Clear the code and verify a clean, correctly-directioned speed trace

Parts/tools involved: Internal transmission wiring harness section.

Cost basis: VinSpecs editorial dataset obd-editorial-us-aftermarket-v1 (US aftermarket, generated 2026-11-14). Verify the diagnosis on your specific vehicle before replacing parts. Report a data error.

← All OBD-II codes Decode your VIN →