P0335 Code — Crankshaft Position Sensor A Circuit Malfunction

P0335: Crankshaft Position Sensor A Circuit Malfunction. This is a Powertrain trouble code — a generic OBD-II code that means the same thing on every make and model. Severity is generally High.

High priority

Misfires can damage the catalytic converter and should be diagnosed promptly. Avoid hard acceleration until fixed.

What the P0335 code means

CodeP0335
DefinitionCrankshaft Position Sensor A Circuit Malfunction
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeGeneric (SAE J2012 standard)
SubsystemIgnition system or misfire
Fault referenceFault #35 within the Powertrain group
Typical severityHigh

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a standardized SAE code, so the definition above applies to any OBD-II compliant vehicle from 1996 onward. Within powertrain codes, it points to the ignition system or misfire area.

Common causes of P0335

P0335 sits in the SAE range covering engine position and timing. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • A failing camshaft (CMP) or crankshaft (CKP) position sensor.
  • A worn or chipped tone wheel the sensor reads.
  • A stretched timing chain or worn guides shifting cam-crank correlation.
  • A sticking VVT actuator or oil control valve (often oil-level sensitive).
  • Wiring or connector faults on the sensor circuit.

Symptoms you may notice with P0335

Codes in the engine position and timing range typically show up like this:

  • Hard starting or no-start (CKP faults).
  • Rough idle and occasional stalling.
  • Reduced power or rattling at startup.
  • Check-engine light with position-correlation codes.

How to fix a P0335 code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: check oil level and condition first (VVT faults track it closely), compare CMP/CKP signals live if you have the tool, and inspect the timing chain only after sensors and wiring test clean.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

Related OBD-II codes

Frequently Asked Questions

What does P0335 mean?

P0335 is a Powertrain diagnostic trouble code that means: Crankshaft Position Sensor A Circuit Malfunction. It is Generic (SAE standard) — the same meaning on every OBD-II vehicle.

Is it safe to drive with a P0335 code?

Misfires can damage the catalytic converter and should be diagnosed promptly. Avoid hard acceleration until fixed.

How do I fix a P0335 code?

Confirm P0335 with an OBD-II scanner, then work the ranked fixes below: start with inspect and reseat the crankshaft position sensor connector (most probable, Easy DIY), verify with a re-scan after each repair. Estimated repair cost ranges from $5 to $59 including labor (editorial estimate, US aftermarket).

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap">

Most likely fixes for P0335, ranked

Ranked by how often the fix resolves the code, based on VinSpecs editorial analysis of US aftermarket repair patterns. Costs are editorial estimates for US aftermarket parts and shop labor (about $110/hour); actual quotes vary by vehicle, region and shop — get a real quote before authorizing work.

1. Inspect and reseat the crankshaft position sensor connector

Probability rank #1 · Difficulty: Easy DIY · Estimated total: $5–$59 (parts $5–$15 + labor 0.4 h)

  1. 1. Locate the sensor near the crank pulley or bellhousing
  2. 2. Unplug and inspect for oil intrusion or corroded pins
  3. 3. Clean contacts and reseat until it clicks
  4. 4. Clear the code and crank the engine to verify a start

Parts/tools involved: Electrical contact cleaner.

2. Replace the crankshaft position sensor

Probability rank #2 · Difficulty: Moderate DIY · Estimated total: $30–$217 (parts $30–$140 + labor 0.7 h)

  1. 1. Remove the sensor's retaining bolt and withdraw it from its bore
  2. 2. Inspect the reluctor wheel/tone ring for damaged teeth or debris
  3. 3. Install the replacement sensor, setting the air gap per spec if not self-adjusting
  4. 4. Clear codes and confirm a stable RPM signal at idle and under load

Parts/tools involved: Crankshaft position sensor.

3. Repair crankshaft position sensor circuit wiring

Probability rank #3 · Difficulty: Professional Required · Estimated total: $10–$219 (parts $10–$65 + labor 1.4 h)

  1. 1. Back-probe the signal, shield, and ground legs at the sensor connector
  2. 2. Voltage-drop test each leg back to the ECM
  3. 3. Repair chafed or corroded conductors with soldered, heat-shrunk splices
  4. 4. Confirm a clean signal waveform on a scope while cranking

Parts/tools involved: Automotive wiring repair kit (solder + heat-shrink).

4. Clean or replace a damaged reluctor wheel/tone ring

Probability rank #4 · Difficulty: Professional Required · Estimated total: $40–$575 (parts $40–$300 + labor 2.5 h)

  1. 1. Remove the sensor and inspect the reluctor wheel through the access bore or with the crank pulley/cover removed
  2. 2. Clean off accumulated debris or rust
  3. 3. Replace a reluctor wheel with bent, missing, or chipped teeth
  4. 4. Reinstall the sensor, reset the gap, and verify a clean signal

Parts/tools involved: Crankshaft reluctor wheel/tone ring.

Cost basis: VinSpecs editorial dataset obd-editorial-us-aftermarket-v1 (US aftermarket, generated 2026-11-14). Verify the diagnosis on your specific vehicle before replacing parts. Report a data error.

← All OBD-II codes Decode your VIN →