P0118 Code — Engine Coolant Temperature Sensor Circuit 1 High Input

P0118: Engine Coolant Temperature Sensor Circuit 1 High Input. This is a Powertrain trouble code — a generic OBD-II code that means the same thing on every make and model. Severity is generally Medium.

Medium priority

Cooling-related faults can lead to overheating. Monitor the temperature gauge and address soon.

What the P0118 code means

CodeP0118
DefinitionEngine Coolant Temperature Sensor Circuit 1 High Input
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeGeneric (SAE J2012 standard)
SubsystemFuel and air metering
Fault referenceFault #18 within the Powertrain group
Typical severityMedium

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a standardized SAE code, so the definition above applies to any OBD-II compliant vehicle from 1996 onward. Within powertrain codes, it points to the fuel and air metering area.

Common causes of P0118

P0118 sits in the SAE range covering engine coolant temperature. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • A thermostat stuck open (engine never warms fully).
  • An ECT sensor drifting out of range.
  • Low coolant or air pockets in the system.
  • Wiring or connector faults at the sensor.

Symptoms you may notice with P0118

Codes in the engine coolant temperature range typically show up like this:

  • Temperature gauge reading low or erratic.
  • Poor fuel economy and weak heater output.
  • Hard starts when cold.
  • Overheating on real cooling faults.

How to fix a P0118 code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: watch ECT live from a cold start: it should climb steadily to about 190-210°F and hold. A reading stuck cold points at the thermostat; a jumpy one at the sensor or wiring.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

Related OBD-II codes

Frequently Asked Questions

What does P0118 mean?

P0118 is a Powertrain diagnostic trouble code that means: Engine Coolant Temperature Sensor Circuit 1 High Input. It is Generic (SAE standard) — the same meaning on every OBD-II vehicle.

Is it safe to drive with a P0118 code?

Cooling-related faults can lead to overheating. Monitor the temperature gauge and address soon.

How do I fix a P0118 code?

Confirm P0118 with an OBD-II scanner, then work the ranked fixes below: start with top off coolant and inspect ect sensor connector (most probable, Easy DIY), verify with a re-scan after each repair. Estimated repair cost ranges from $10 to $74 including labor (editorial estimate, US aftermarket).

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap">

Most likely fixes for P0118, ranked

Ranked by how often the fix resolves the code, based on VinSpecs editorial analysis of US aftermarket repair patterns. Costs are editorial estimates for US aftermarket parts and shop labor (about $110/hour); actual quotes vary by vehicle, region and shop — get a real quote before authorizing work.

1. Top off coolant and inspect ECT sensor connector

Probability rank #1 · Difficulty: Easy DIY · Estimated total: $10–$74 (parts $10–$30 + labor 0.4 h)

  1. 1. Check coolant level and top off with the correct spec coolant
  2. 2. Unplug the ECT sensor connector and inspect for corrosion
  3. 3. Clean contacts and reconnect
  4. 4. Clear codes and monitor warm-up temperature curve

Parts/tools involved: Coolant (OEM-spec type).

2. Replace engine/radiator coolant temperature sensor

Probability rank #2 · Difficulty: Moderate DIY · Estimated total: $15–$136 (parts $15–$70 + labor 0.6 h)

  1. 1. Relieve cooling system pressure and drain coolant to below sensor level
  2. 2. Remove the sensor from the head, housing, or radiator tank
  3. 3. Install the replacement sensor with sealant or new seal as specified
  4. 4. Refill coolant, bleed air, and clear codes

Parts/tools involved: Coolant temperature sensor, Coolant (OEM-spec type).

3. Repair coolant temperature sensor wiring

Probability rank #3 · Difficulty: Professional Required · Estimated total: $10–$192 (parts $10–$60 + labor 1.2 h)

  1. 1. Measure sensor resistance at the connector against a temperature/resistance chart
  2. 2. Voltage-drop test the circuit back to the ECM
  3. 3. Repair chafed or corroded wiring with heat-shrink splices
  4. 4. Confirm reading tracks actual coolant temperature

Parts/tools involved: Automotive wiring repair kit (solder + heat-shrink).

Cost basis: VinSpecs editorial dataset obd-editorial-us-aftermarket-v1 (US aftermarket, generated 2026-11-14). Verify the diagnosis on your specific vehicle before replacing parts. Report a data error.

← All OBD-II codes Decode your VIN →