P2197 Code — O2 Sensor Signal Stuck Lean Bank 2 Sensor 1
P2197: O2 Sensor Signal Stuck Lean Bank 2 Sensor 1. This is a Powertrain trouble code — a manufacturer-specific code whose exact meaning can vary by carmaker. Severity is generally Medium.
Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.
What the P2197 code means
| Code | P2197 |
|---|---|
| Definition | O2 Sensor Signal Stuck Lean Bank 2 Sensor 1 |
| System | Powertrain — engine, transmission and associated drivetrain systems |
| Code type | Manufacturer-specific |
| Subsystem | Fuel and air metering |
| Fault reference | Fault #97 within the Powertrain group |
| Typical severity | Medium |
The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a manufacturer-defined code, so confirm the exact meaning against your carmaker's service information. Within powertrain codes, it points to the fuel and air metering area.
Common causes of P2197
P2197 sits in the SAE range covering oxygen (O2) sensor circuit. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:
- An aged sensor with slow voltage response.
- A failed heater element or its fuse/relay circuit.
- Contamination from coolant, oil or fuel additives.
- An exhaust leak upstream of the sensor skewing the reading.
- Wiring or connector faults (chafing near the exhaust is common).
Symptoms you may notice with P2197
Codes in the oxygen (O2) sensor circuit range typically show up like this:
- Poor fuel economy.
- Rough idle or hesitation.
- A failed emissions test.
- Often no drivability change (heater faults).
How to fix a P2197 code
- Read and record the code with an OBD-II scanner, along with any freeze-frame data.
- Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
- Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
- Clear the code and drive a full cycle, then re-scan to confirm it does not return.
Where to look first: watch the sensor switching frequency live at 2,000 rpm, confirm heater resistance against spec, and check for exhaust leaks before condemning the sensor.
Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.
What repairs in this range typically cost
P2197 itself is not in VinSpecs' ranked-fixes dataset yet, but across 23 comparable codes in the same SAE subsystem, editorial US-aftermarket repair totals (parts + shop labor at $110/hour) ranged $0–$670. Get a quote for your specific vehicle before authorizing work — the ranked-fixes example for P0101 shows how a covered code in this range is priced.
Related OBD-II codes
Frequently Asked Questions
What does P2197 mean?
P2197 is a Powertrain diagnostic trouble code that means: O2 Sensor Signal Stuck Lean Bank 2 Sensor 1. It is Manufacturer-specific — the exact meaning can vary by carmaker.
Is it safe to drive with a P2197 code?
Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.
How do I fix a P2197 code?
Confirm P2197 with an OBD-II scanner, then start with the sensor switching rate live at 2,000 rpm and its heater resistance. Repair or replace the confirmed faulty part, clear the code and re-scan after a drive cycle. A professional diagnosis is recommended if you are unsure.
Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.
flex;gap:.6rem;flex-wrap:wrap"> ← All OBD-II codes Decode your VIN →
Related Guides
Free, data-backed reading that goes deeper on what this page covers: