P07AE Code — Transmission Friction ElementGPerformance/Stuck Off

P07AE: Transmission Friction ElementGPerformance/Stuck Off. This is a Powertrain trouble code — a generic OBD-II code that means the same thing on every make and model. Severity is generally Medium.

Medium priority

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

What the P07AE code means

CodeP07AE
DefinitionTransmission Friction ElementGPerformance/Stuck Off
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeGeneric (SAE J2012 standard)
SubsystemTransmission
Fault referenceFault #AE within the Powertrain group
Typical severityMedium

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a standardized SAE code, so the definition above applies to any OBD-II compliant vehicle from 1996 onward. Within powertrain codes, it points to the transmission area.

Common causes of P07AE

P07AE sits in the SAE range covering transmission. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • Low, burnt or wrong-spec transmission fluid.
  • Failed pressure control or shift solenoids (electrical or stuck).
  • Valve-body wear or a stuck valve.
  • Torque converter clutch (TCC) solenoid or its circuit.
  • Wiring or connector faults between the TCM and the solenoids.

Symptoms you may notice with P07AE

Codes in the transmission range typically show up like this:

  • Harsh, delayed or flaring shifts.
  • Slipping under load.
  • Stuck in one gear or a limp-home mode.
  • Shudder at converter lockup.

How to fix a P07AE code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: check the fluid level and condition first (many solenoid codes start there), then test solenoid resistance and command them on/off with a scan tool before opening the pan.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

What repairs in this range typically cost

P07AE itself is not in VinSpecs' ranked-fixes dataset yet, but across 8 comparable codes in the same SAE subsystem, editorial US-aftermarket repair totals (parts + shop labor at $110/hour) ranged $5–$420. Get a quote for your specific vehicle before authorizing work — the ranked-fixes example for P0700 shows how a covered code in this range is priced.

Related OBD-II codes

Frequently Asked Questions

What does P07AE mean?

P07AE is a Powertrain diagnostic trouble code that means: Transmission Friction ElementGPerformance/Stuck Off. It is Generic (SAE standard) — the same meaning on every OBD-II vehicle.

Is it safe to drive with a P07AE code?

Have the vehicle scanned and the root cause confirmed before extended driving. Severity depends on the specific fault and symptoms.

How do I fix a P07AE code?

Confirm P07AE with an OBD-II scanner, then start with the transmission fluid level and condition, then commanded solenoid tests. Repair or replace the confirmed faulty part, clear the code and re-scan after a drive cycle. A professional diagnosis is recommended if you are unsure.

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap"> ← All OBD-II codes Decode your VIN →