P060F Code — Internal Control Module Coolant Temperature Performance

P060F: Internal Control Module Coolant Temperature Performance. This is a Powertrain trouble code — a generic OBD-II code that means the same thing on every make and model. Severity is generally Medium.

Medium priority

Cooling-related faults can lead to overheating. Monitor the temperature gauge and address soon.

What the P060F code means

CodeP060F
DefinitionInternal Control Module Coolant Temperature Performance
SystemPowertrain — engine, transmission and associated drivetrain systems
Code typeGeneric (SAE J2012 standard)
SubsystemComputer output circuits
Fault referenceFault #0F within the Powertrain group
Typical severityMedium

The letter P tells you the code belongs to the Powertrain family, covering engine, transmission and associated drivetrain systems. The second digit shows this is a standardized SAE code, so the definition above applies to any OBD-II compliant vehicle from 1996 onward. Within powertrain codes, it points to the computer output circuits area.

Common causes of P060F

P060F sits in the SAE range covering engine coolant temperature. Components in that range fail in predictable ways, so the usual suspects here are specific rather than generic. Confirm the actual fault with a scan before replacing parts:

  • A thermostat stuck open (engine never warms fully).
  • An ECT sensor drifting out of range.
  • Low coolant or air pockets in the system.
  • Wiring or connector faults at the sensor.

Symptoms you may notice with P060F

Codes in the engine coolant temperature range typically show up like this:

  • Temperature gauge reading low or erratic.
  • Poor fuel economy and weak heater output.
  • Hard starts when cold.
  • Overheating on real cooling faults.

How to fix a P060F code

  1. Read and record the code with an OBD-II scanner, along with any freeze-frame data.
  2. Inspect the wiring, connectors and components in the Powertrain circuit the code points to.
  3. Repair or replace the confirmed faulty part — avoid swapping parts on a guess.
  4. Clear the code and drive a full cycle, then re-scan to confirm it does not return.

Where to look first: watch ECT live from a cold start: it should climb steadily to about 190-210°F and hold. A reading stuck cold points at the thermostat; a jumpy one at the sensor or wiring.

Recall repairs are free at a dealer, so it is worth checking for an open recall or decoding your VIN before paying for diagnostics — some faults are covered.

What repairs in this range typically cost

P060F itself is not in VinSpecs' ranked-fixes dataset yet, but across 1 comparable codes in the same SAE subsystem, editorial US-aftermarket repair totals (parts + shop labor at $110/hour) ranged $5–$1,065. Get a quote for your specific vehicle before authorizing work — the ranked-fixes example for P0606 shows how a covered code in this range is priced.

Related OBD-II codes

Frequently Asked Questions

What does P060F mean?

P060F is a Powertrain diagnostic trouble code that means: Internal Control Module Coolant Temperature Performance. It is Generic (SAE standard) — the same meaning on every OBD-II vehicle.

Is it safe to drive with a P060F code?

Cooling-related faults can lead to overheating. Monitor the temperature gauge and address soon.

How do I fix a P060F code?

Confirm P060F with an OBD-II scanner, then start with the ECT reading watched live from a cold start (thermostat vs sensor). Repair or replace the confirmed faulty part, clear the code and re-scan after a drive cycle. A professional diagnosis is recommended if you are unsure.

Code definition sourced from the open-source OBD-II code dataset (SAE J2012 / ISO 15031 standard). VinSpecs is an independent service and is not affiliated with any vehicle manufacturer.

flex;gap:.6rem;flex-wrap:wrap"> ← All OBD-II codes Decode your VIN →